Automatic Center Punch

sku: 8141100

An extremely accurate tool which allows variable impressions by simply adjusting the knurled head. When depressed, a sharp blow results. Hammering is not required. Measures 4-3/4" overall length. Made in India.

Bench Block Helper with Steel & Nylon Blocks

sku: 8121645

This 3-piece set includes a thick vulcanized firm rubber base which absorbs shock plus a solid steel block which is 15/16" (24mm) thick and 3" (75mm) in diameter. The third piece is a sturdy nylon block the same size that fits into the rubber...

Del Rey™ Center Punch

sku: 8141103

Use the Del Rey™ center punch to mark metal in preparation for drilling.  Hit the end with a hammer (not included) to create a small dimple which will help you center your drill when creating holes.  Can also serve as a scribe for design layout...

Durston Bangle Forming Die Set

sku: 8141057

This well made product from Durston helps you effortlessly form bangles and cuffs. Fits all standard bench vises. These dies and holder are precision ground, highly polished and hardened to last (with proper use). Set includes, special convex...

Fretz B-1 Flat Bezel Stake

sku: 8141061

This B-1 stake is distinguished by its sharp edge and flat top so you can hammer out sharp right angles without tedious cutting and mitering.   Use pliers to shape the bezel sheet around the stone as closely as possible, then use the stakes...

Fretz B-2 Sharp Edge Low Dome Bezel Stake

sku: 8141062

This B-2 stake is distinguished by its sharp edge and slightly domed top so you can hammer out sharp right angles without tedious cutting and mitering.   Use pliers to shape the bezel sheet around the stone as closely as possible, then use the...

Fretz B-3 Sharp Edge High Dome Bezel Stake

sku: 8141063

This B-3 stake is distinguished by its sharp edge and a high domed top so you can hammer out sharp right angles without tedious cutting and mitering.   Use pliers to shape the bezel sheet around the stone as closely as possible, then use the...

Fretz B-4 Trillion Undercut Bezel Stake

sku: 8141064

This B-4 stake is undercut for use with trillion and pear-shaped stones. Use pliers to shape the bezel sheet around the stone as closely as possible, then use the stakes to gradually stretch the sheet to match the corresponding curves and angles of the...

Fretz B-5 Rolled Edge Flat Stake

sku: 8141065

This B-5 stake is distinguished by its rolled edge and flat top allowing you to hammer out bezels without tedious cutting and mitering.   Use pliers to shape the bezel sheet around the stone as closely as possible, then use the stakes to...

Fretz B-6 Rolled Edge Dome Bezel Stake

sku: 8141066

This B-6 stake has a rolled edge and domed top allowing you to hammer out bezels without tedious cutting and mitering.   Use pliers to shape the bezel sheet around the stone as closely as possible, then use the stakes to gradually stretch the...

FRETZ BA-1 Bench Anvil Flat

sku: 8141301

The BA-1 Bench Anvil mushroom stake has a flat top for flattening and texturing metal, but can also use the slightly rounded edges to create nearly 90-degree angles in your workpieces. These anvils feature hardened 420 stainless steel tops that have a...

FRETZ BA-2 Bench Anvil Low Dome

sku: 8141302

This MA-2 low dome bench anvil is a mushroom stake that is ideal for creating slight curves in jewelry forms. Fretz Bench Anvils feature hardened 420 stainless steel tops that have a high polish to prevent scratching your jewelry metal. The hardwood...

FRETZ BA-3 Bench Anvil Med Dome

sku: 8141303

This medium dome bench anvil is a mushroom stake that allows you to shape and texture sheet metal.  Fretz Bench Anvils feature hardened 420 stainless steel tops that have a high polish to prevent scratching your jewelry metal. The hardwood...

FRETZ BA-4 Bench Anvil Hi Dome

sku: 8141304

This high dome bench anvil is a mushroom stake that allows you to shape and texture sheet metal. Fretz Bench Anvils feature hardened 420 stainless steel tops that have a high polish to prevent scratching your work.  Features a wooden base to absorb...

FRETZ BA-5 Bench Anvil Square Dome

sku: 8141305

The BA-5 Bench Anvil is a 75mm (approx.3") square block which features a flat top ideal for flattening curves and four different top edges which you can translate into your jewelry metal through repeated hammer blows. The 4 edges are a sharp 90-degree, a...

FRETZ BH-1 Blow Horn Stake

sku: 8141120

With a design based on a classic tinsmithing stake, the Fretz BH-1 Blow Horn Stake is perfect for forging bracelets and cuffs. You can also use the BH-1 to thin and raise thick stock. Compatible with Fretz H-101 and VF-101 holders (even though shown in...

FRETZ E-100 Extractor Wedge

sku: 8141042

This extractor wedge can come in handy if a Fretz M-100 Series Stake becomes stuck in the E-101 Holder. Simply drive the E-100 Extractor Wedge into the oval hole in the E-101 to free the stake. Made in Vietnam.

FRETZ E-101 & E-100 Holder and Wedge Set

sku: 8141043

Money saving set consisting of both the E-101 holder and the E100 extractor wedge.  If your Fretz M-100 Series Stake becomes stuck in the E-101 Holder, you'll wish you had the wedge at your fingertips! You simply drive the E-100 Extractor Wedge into...

FRETZ E-101 Extender Holder

sku: 8141041

 This E-101 extends the reach of the Fretz M-100 Series Mushroom Stakes by 80mm for assistance when forming large, curved shapes. The E-101 is designed to fit into the H-101 or the VH-101 Stake Holders (not included). Made in Vietnam.

FRETZ E-102 Curved Extender

sku: 8141044

 The unique curved shape of the E-102 holder positions the Fretz M-100 Series Mushroom Stakes uniquely which can be the exact striking angle you need but have trouble obtaining with any other holder.   The E-102is designed to fit into the...

Fretz F-1 Beak Miniature Forming Stake

sku: 8141092

A classic silversmithing stake on a jewelry-making scale, the F-1 Beak Stake features two ends with a slight taper, which will translate into your metal through repeated hammer blows. Fretz stakes are made from hardened 420-grade stainless steel with...

FRETZ F-101 Large Beak Stake

sku: 8141114

The Fretz F-101 Large Beak Stake is specifically designed for shaping steep domes on bracelets and hollowware, but if you utilize every piece of the stake, you can use it to create almost any form. Compatible with Fretz H-101 and VF-101 holders (shown in...

FRETZ F-102 Large Double Convex Stake

sku: 8141115

The Fretz F-102 Large Double Convex Stake has two highly rounded ends perfect for forming deep domed shapes in your jewelry. By using the stake’s various curves and edges, you can achieve nearly any form you desire. Compatible with Fretz H-101 and VF-101...

FRETZ F-103 Large Doming Stake

sku: 8141116

The Fretz F-103 Large Doming Stake has been designed to dome flat sheet metal, but you can also use it to forge heavy metal stock into convex or concave shapes. Compatible with Fretz H-101 and VF-101 holders (shown in a holder in the picture but all...

Fretz F-2 Double Convex Miniature Forming Stake

sku: 8141089

The Fretz F-2 Double Convex Stake features two convex ends: one large for forming large, dramatic curves and one small for doming sheet metal. Using this stake helps you form domed bracelets, rings or bead shapes from flat tubular shapes.  The...

Fretz F-2A Lining Convex Flute Stake

sku: 8141106

Use this F-2A lining stake to begin to shape concave flutes. Draw the design lines with a sharp ink marker on the hollow metal domed shape.   For straight flutes use a straight hammer (consider our 8217031 HMR-2 Wide or our 8217032 HMR-3...

FRETZ F-2B Sharp Convex Flute Stake

sku: 8141107

Generally you would already have a basic concave flute created on your piece before you would use this F-2B stake to further refine the shape.  That is why this stake is available both individually and in a set (8141109) so you can easily use the...

FRETZ F-2C Extreme Sharp Convex Flute Stake

sku: 8141108

This F-2C stake is usually used to finish a concave flute by sharpening the high points.  That is why this stake is available both individually and in a set (8141109) so you can easily use the flute stakes in succession.  After beginning the...

FRETZ F-3 Doming Miniature Forming Stake

sku: 8141095

The F-3 Doming Stake from Fretz has two concave ends and a slightly rounded top for shaping rings, bezels, and other small domed shapes. Fretz stakes are made from hardened 420-grade stainless steel with highly polished areas to prevent scratching or...

FRETZ F-4 Cone Miniature Forming Stake

sku: 8141096

The Fretz F-4 Cone Stake features two tapering ends: one large and one small to form conical shapes of different sizes. You can also use the wide middle section to make concave curves in sheet metal. Fretz stakes are made from hardened 420-grade...

FRETZ F-5 Hoop Doming Miniature Forming Stake

sku: 8141097

Designed for making hoop shapes like earrings and rings, the F-5 Hoop Doming Stake from Fretz features two ends with flat faces perfect for forming tight curves. Fretz stakes are made from hardened 420-grade stainless steel with highly polished areas to...

Fretz F-6 Shell Miniature Forming Stake

sku: 8141091

An incredibly versatile jewelry-making stake, the Fretz F-6 Shell Stake can be used to make bracelet sized shell-forms, bold concave shapes and narrow convex shapes, so you can create a range of anticlastic forms. Fretz stakes are made from hardened...

Fretz F-7 Thin Shell Miniature Forming Stake

sku: 8141093

This F-7 Thin Shell Stake is narrower than the F-6 so is perfect for forming small convex and concave curves to yield small-scale anticlastic shapes. Fretz stakes are made from hardened 420-grade stainless steel with highly polished areas to prevent...

Fretz F-8 Horn Miniature Forming Stake

sku: 8141094

A classic silversmithing shape but on a jeweler’s scale, the F-8 Horn Stake is designed for hammering out hollow domed shapes, like making beads from tubes or bracelets or hollow rings, from sheet metal. Fretz stakes are made from hardened 420-grade...

Fretz F-9 Convex/Concave Miniature Forming Stake

sku: 8141090

Use the F-9 Convex/Concave Stake to make a range of synclastic and anticlastic forms from shallow concave curves to S-shaped sculptures. One side is convex and allows you to make a shallow dome. The other side is for making concave bracelet sized jewelry...

Fretz FP-1 Wide Convex Cuff DVD & Tool Set

sku: 8218411

The Fretz FP-1 set included the tools (hammer and stakes) you need as well as the DVD to follow along - allowing you to make your own Wide Convex Cuff jewelry.  This package is such and excellent way to get started so it also makes a terrific gift...

Fretz FP-2 Set Wide Concave Cuff DVD & Tools

sku: 8218412

Terrific set which includes the hammers and stakes you need to follow along and make your own Wide Concave Cuff jewelry .  Excellent way to get started - and this set makes a terrific gift for someone who is starting out and doesn't already have the...

Fretz FP-3 Set Wide Convex and Concave Cuffs DVD & Tools

sku: 8218413

Everyone who wants to make wide cuff jewelry - both Concave and Convex - this set is exactly what you need.  Comes with 2 DVDs for instruction and all the tools you need to get started, plus a handy storage rack.  Makes an excellent gift for...

FRETZ G-1 Hook Stake 200mm 291g

sku: 8141141

Use the small single curve of this G-1 Hook to make complex shapes without your jewelry metal binding to the stake. Bill Fretz and Michael Good worked together to develop stakes and hammers for Michael Good’s specialty: anticlastic raising. These hook...

FRETZ G-2 Hook Stake 200mm 287g

sku: 8141142

This G-2 Hook has a steeper curve allowing you to deepen your anticlastic forms; all without your jewelry metal binding to the stake. Bill Fretz and Michael Good worked together to develop stakes and hammers for Michael Good’s specialty: anticlastic...

FRETZ G-3 Hook Stake 200mm 188g

sku: 8141143

This G-3 Hook is used for small work or to close larger anticlastic forms; all without your jewelry metal binding to the stake. Bill Fretz and Michael Good worked together to develop stakes and hammers for Michael Good’s specialty: anticlastic raising...

FRETZ G-4 Hook Stake 200mm 182g

sku: 8141144

The G-4 Hook is used for small-scale forming and for tightening anticlastic forms.  All the while, your metal will not bind to the stake.   Bill Fretz and Michael Good worked together to develop stakes and hammers for Michael Good’s...

FRETZ G-5 Hook Stake 200mm 186g

sku: 8141145

 The G-5 Hook is made for very small work and for further tightening anticlastic forms.  Bill Fretz and Michael Good worked together to develop stakes and hammers for Michael Good’s specialty: anticlastic raising. These hook stakes can be used...

FRETZ G-6 Hook Stake 200mm 188g

sku: 8141146

The G-6 is usually used to form small anticlastic forms and to close tiny speculums.  Bill Fretz and Michael Good worked together to develop stakes and hammers for Michael Good’s specialty: anticlastic raising. These hook stakes can be used...

FRETZ GH-1 Holder 85x78mm 293g

sku: 8141140

The GH-1 Holder is made to hold the Fretz line of Michael Good stakes. The screw on top keeps the stakes in place while the tapered tang is held in a vise. Made in Vietnam. 

FRETZ H-101 Holder

sku: 8141047

This H-101 holds the larger Fretz 100 Series Stakes to give you maximum control and flexibility while using larger stakes. The H-101 is designed to be mounted onto a sturdy base like your bench with socket head bolts and nuts (included). Made in Vietnam...

FRETZ H-1L Long Holder

sku: 8141051

The H-1L Long Holder holds all the Fretz Bezel T, Miniature Mushroom, Miniature Forming Stakes plus the M-100 Series Mushroom Stakes. The H-1L’s extended length gives you extra room for larger forming projects without worrying about striking your bench...

FRETZ H-2 5mm Accessory Tool Holder

sku: 8141084

The H-2 is a very small holder for Fretz Micro Mandrels, Micro Stakes, and Insert Wheels. The H-2 fits into the H-1 (not included) for very small-scale forming tasks. Made in Vietnam.

FRETZ I-1 4.7mm Round High Dome Insert

sku: 8141271

This Fretz I-1 Insert can be used to create variety of shapes in small and large projects from shimmering dimples to 4.7mm high domes. Designed to be used with the Fretz H-2 Stake Holder (not included although it is shown in the picture) insert this into...

FRETZ I-10 35x4x13.8mm Taper

sku: 8141280

The Fretz I-10 Taper Insert is perfect for creating small concave shapes. The I-10 Insert tapers from a 13.8mm diameter at its thickest point to its 4mm face. Designed to be used with the Fretz H-2 Stake Holder (sold separately). Fretz stakes are made...